As a representative of artificial tillage, small sowing machines such as peanut automatic sowing machines have gradually entered thousands of households. From the advanced design and advanced conception of the peanut automatic sowing machine, the modern development changes are reflected in the best. Now we introduce the maintenance and maintenance of the peanut automatic sowing machine.
1. The peanut automatic sowing machine should fill the oil injection points in time before work to ensure that the running parts are fully lubricated. Lost or damaged parts should be replenished, replaced and repaired in time. Be careful not to apply oil to the gears and chains to avoid sticking to the soil and increase wear.
2. Each row of seed wheels has the same working length and the same displacement. The automatic sowing machine's sowing volume adjustment mechanism is flexible, and there must be no sliding or air movement.
3. The disc opener disc is flexible to rotate, and must not be shaken, and does not rub against the opener body.
4. Before and after the work, the soil of all parts of the automatic sowing machine should be cleaned, paying special attention to remove the dirt and oil on the transmission system.
5. After the end of each shift, the fertilizer in the automatic sowing machine fertilizer tank should be cleaned to prevent the fertilizer from corroding the fertilizer tank and the fertilizer discharge site. Check if the seed shaft and the fertilizer shaft are flexible.
6. After each shift, the automatic sowing machine should be parked in a dry, covered shed. When parking in the open air, the fertilizer box should be tightly closed. When the container is parked, the ditch is lowered, the device is lowered, and the support is lowered to stabilize the body, so that unnecessary load is reduced on the frame of the automatic sowing machine.
Thursday, October 24, 2019
Peanut automatic sowing machine notes
The automatic sowing machine uses the crop seeds as the planting machine for the seeding object. Peanut automatic sowing machines for certain types of crops often referred to as crop species names, such as grain drills, corn seed drills, cotton peanut automatic seeders, pasture spreaders, etc. The following Shuliy machinery introduces you to the automatic sowing machine notes:
1. Check whether the seeding parts are defective before use, whether there is any foreign matter in the seedbox, and oiling the parts to be oiled;
2, before the spring sowing, should be prepared for vulnerable mechanical parts, so as not to delay planting, delay farming time. The seeds must be dry and clean and do not contain debris such as straw and stones, so as to avoid blocking the seeding mouth and affect the quality of the seeding. When sowing seeds, the seeds should be carefully selected, otherwise the quality of the seeding will be affected.
3. Do a single port flow test to ensure accurate seeding;
4. Prepare for seeding. When planting, we must grasp the matters of sowing, turning, and work. The peanut sowing machine should avoid parking when working. When parking must be stopped, in order to prevent the phenomenon of “broken strip”, the peanut planter should be raised and retreated for a distance. Sowing. When descending the peanut planter, the tractor is to be carried out slowly.
5. When starting work, the hydraulic control handle should be placed in a floating position.
6. Pay attention to safety during operation to prevent safety accidents;
7. Maintenance of tools and cleaning of debris during operation should be carried out with the unit being parked and stabilized.
8. When parking is adjusted, the machine power should be cut off.
9. The machine is not allowed to reverse or turn in the working state. .
10. When the unit is turning before or during long-distance transportation, the peanut planter should be raised to cut off the power of the seed meter.
11. The operator should observe the operation status of the peanut planter at any time during the operation. Pay special attention to whether the seed meter is seeded, whether the seed tube is blocked or not, and whether there are enough seeds in the seed box. When planting seeds mixed with pesticides, the seeder should wear protective tools such as gloves, masks, and goggles. The remaining seeds should be disposed of in a timely manner and must not be dumped or littered anywhere, so as not to pollute the environment and cause harm to humans and animals.
12. After use, clean the peanut planter and give the chain and other parts a butter control rust.
1. Check whether the seeding parts are defective before use, whether there is any foreign matter in the seedbox, and oiling the parts to be oiled;
2, before the spring sowing, should be prepared for vulnerable mechanical parts, so as not to delay planting, delay farming time. The seeds must be dry and clean and do not contain debris such as straw and stones, so as to avoid blocking the seeding mouth and affect the quality of the seeding. When sowing seeds, the seeds should be carefully selected, otherwise the quality of the seeding will be affected.
3. Do a single port flow test to ensure accurate seeding;
4. Prepare for seeding. When planting, we must grasp the matters of sowing, turning, and work. The peanut sowing machine should avoid parking when working. When parking must be stopped, in order to prevent the phenomenon of “broken strip”, the peanut planter should be raised and retreated for a distance. Sowing. When descending the peanut planter, the tractor is to be carried out slowly.
5. When starting work, the hydraulic control handle should be placed in a floating position.
6. Pay attention to safety during operation to prevent safety accidents;
7. Maintenance of tools and cleaning of debris during operation should be carried out with the unit being parked and stabilized.
8. When parking is adjusted, the machine power should be cut off.
9. The machine is not allowed to reverse or turn in the working state. .
10. When the unit is turning before or during long-distance transportation, the peanut planter should be raised to cut off the power of the seed meter.
11. The operator should observe the operation status of the peanut planter at any time during the operation. Pay special attention to whether the seed meter is seeded, whether the seed tube is blocked or not, and whether there are enough seeds in the seed box. When planting seeds mixed with pesticides, the seeder should wear protective tools such as gloves, masks, and goggles. The remaining seeds should be disposed of in a timely manner and must not be dumped or littered anywhere, so as not to pollute the environment and cause harm to humans and animals.
12. After use, clean the peanut planter and give the chain and other parts a butter control rust.
Thursday, October 17, 2019
How to use small corn thresher
Due to the regional differentiation, large-scale threshers can not be entered in some areas, such as remote mountain villages and farmers living in the mountains. At this time, the small corn thresher solves the problem of farmers for these farmers.
After many farmers in their lives bought a small corn thresher, they still don't know how to use it properly. This article will explain how to use a small thresher in the following aspects.
1. Level the four feet of the equipment to ensure a smooth and firm. To reduce vibration.
2. If the motor is used as the power, it is necessary to check whether the power cord is firmly connected, tightly wrapped and installed with the ground wire.
3. Feed the corn cob continuously and evenly, and the feeding amount should be suitable. If the feeding is intermittent, it will affect production efficiency. If the feeding amount is too much, the machine will be stuck and overloaded, which will cause the motor to burn and damage the equipment.
4. The water content of the threshed corn cob should not exceed 20%, and the water content is too high to reach the normal threshing effect.
5. Before the end of the work, the corn cobs that have been put into operation will be completely cleaned and discharged, and then the load will be stopped.
The joint of the rotating belt should be firm; it is strictly forbidden to pick up the belt or touch any object to the east when the machine is running.
6. It is necessary to pay attention to the rotation ratio between the supporting power and the thresher to meet the requirements, so as to avoid personal injury caused by the high speed of the thresher, the rotation is severe, the parts are damaged or the loosening of the product is loose.
7, can not continue to work for too long, generally work about 8 hours to stop inspection, adjustment, and lubrication, to prevent friction caused by wear, heat and deformation.
8. The thresher is generally powered by a diesel engine. A fire hood should be worn on the exhaust pipe to prevent fire.
9. If the threshing machine has a fault during the operation, it should be stopped and repaired and adjusted.
The above is the correct use of the small thresher. The corn thresher produced by the factory is bulky and not suitable for the farmers in the mountainous area. For mountainous areas with developed roads, the automatic corn thresher can also meet the needs of farmers for threshing.
After many farmers in their lives bought a small corn thresher, they still don't know how to use it properly. This article will explain how to use a small thresher in the following aspects.
1. Level the four feet of the equipment to ensure a smooth and firm. To reduce vibration.
2. If the motor is used as the power, it is necessary to check whether the power cord is firmly connected, tightly wrapped and installed with the ground wire.
3. Feed the corn cob continuously and evenly, and the feeding amount should be suitable. If the feeding is intermittent, it will affect production efficiency. If the feeding amount is too much, the machine will be stuck and overloaded, which will cause the motor to burn and damage the equipment.
4. The water content of the threshed corn cob should not exceed 20%, and the water content is too high to reach the normal threshing effect.
5. Before the end of the work, the corn cobs that have been put into operation will be completely cleaned and discharged, and then the load will be stopped.
The joint of the rotating belt should be firm; it is strictly forbidden to pick up the belt or touch any object to the east when the machine is running.
6. It is necessary to pay attention to the rotation ratio between the supporting power and the thresher to meet the requirements, so as to avoid personal injury caused by the high speed of the thresher, the rotation is severe, the parts are damaged or the loosening of the product is loose.
7, can not continue to work for too long, generally work about 8 hours to stop inspection, adjustment, and lubrication, to prevent friction caused by wear, heat and deformation.
8. The thresher is generally powered by a diesel engine. A fire hood should be worn on the exhaust pipe to prevent fire.
9. If the threshing machine has a fault during the operation, it should be stopped and repaired and adjusted.
The above is the correct use of the small thresher. The corn thresher produced by the factory is bulky and not suitable for the farmers in the mountainous area. For mountainous areas with developed roads, the automatic corn thresher can also meet the needs of farmers for threshing.
Shuliy Large Corn Thresher
The large corn thresher separates the corn kernels and stems, and the threshing depth is adjustable. Suitable for food processing plants in conjunction with rapid freezing and canned corn producers.
The design is reasonable--the whole machine is made of all stainless steel, which is convenient to move with the casters; the operation is simple; the discharge port is equipped with a powerful blower and vibrating screen, which further filters and filters the sweet corn kernels that are removed when the impurities are blown away. Clean and beautiful! Suitable for all kinds of fresh, sweet, waxy corn, frozen corn and threshed after thawing.
5TY series corn thresher, when working, the corn is fed by the feeding port, the corn is impacted in the rotor and the drum rotating at high speed, the grain is separated by the sieve hole, the corn cob is discharged from the tail of the machine, the corn silk is discharged from the tuyere. . The feed port is located at the upper part of the upper cover of the machine.
The corn cob enters the threshing chamber through the feeding port, and the rotor that is subjected to high-speed rotation in the threshing chamber hits the corn kernels and falls off, and is separated through the mesh hole. The lower part of the feeding inlet has a baffle to prevent the falling corn kernels from splashing and injuring people. In this kind of machine, the efficiency of threshing is determined by the length and diameter of the drum. Users can choose this series of corn thresher according to their own threshing efficiency. The nail teeth on the rotor are wearing parts. The wear condition should be checked frequently. When the nail teeth wear a quarter of the teeth, the new nails can be repaired or replaced by electric welding. If the new nails are repaired, they must be repaired or replaced. To ensure the balance of the rotor; the screen is a wearing part, if the screen is broken, please replace the new screen.
The design is reasonable--the whole machine is made of all stainless steel, which is convenient to move with the casters; the operation is simple; the discharge port is equipped with a powerful blower and vibrating screen, which further filters and filters the sweet corn kernels that are removed when the impurities are blown away. Clean and beautiful! Suitable for all kinds of fresh, sweet, waxy corn, frozen corn and threshed after thawing.
5TY series corn thresher, when working, the corn is fed by the feeding port, the corn is impacted in the rotor and the drum rotating at high speed, the grain is separated by the sieve hole, the corn cob is discharged from the tail of the machine, the corn silk is discharged from the tuyere. . The feed port is located at the upper part of the upper cover of the machine.
The corn cob enters the threshing chamber through the feeding port, and the rotor that is subjected to high-speed rotation in the threshing chamber hits the corn kernels and falls off, and is separated through the mesh hole. The lower part of the feeding inlet has a baffle to prevent the falling corn kernels from splashing and injuring people. In this kind of machine, the efficiency of threshing is determined by the length and diameter of the drum. Users can choose this series of corn thresher according to their own threshing efficiency. The nail teeth on the rotor are wearing parts. The wear condition should be checked frequently. When the nail teeth wear a quarter of the teeth, the new nails can be repaired or replaced by electric welding. If the new nails are repaired, they must be repaired or replaced. To ensure the balance of the rotor; the screen is a wearing part, if the screen is broken, please replace the new screen.
Subscribe to:
Comments (Atom)